Otros

Faymonville 3-Achs-Beton-Innenlader PREFAMAX

Gooseneck:
• Gooseneck designed as a loading area with aluminum tear plate covering
• Hydraulic lifting arm can be raised and lowered by approx. -280/+250 mm.
• Two kingpin positions at approx. 2,300 mm and approx. 2,000 mm
• For tractor unit: 4 x 2, 6 x 2 or 6 x 4

Loading shaft:
• Loading shaft, length approx. 9,500 mm, with angle profiles attached at the bottom to accommodate the loading pallets
• (Distance from kingpin to the middle of the axle assembly approx. 8,000 mm)

Axles, suspension and tires:
• BPW axle stubs, with drum brakes and independent wheel suspension, hydraulic axle compensation with lifting and lowering device
• Lowering protection on the axles in the event of a suspension hose burst, designed for pallet heights of max. 150 mm
• Axle tool
• Tires 385/65 R 22.5 (M+S)

Brake system:
• EBS brake system from WABCO in accordance with EU regulations

Lighting system:
• 24-volt lighting system in "ASPÖCK-NORDIK" (ASS 3), design in accordance with EU regulations
• ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin socket
• 24N connection in accordance with ISO-1185
• 24S connection in accordance with ISO-3731
• 15-pin connection in accordance with ISO-12098

Painting:
• 6-K final treatment:
• Complete steel construction shot-blasted after welding
• One layer of zinc-based base paint, one layer of adhesion primer
• Final painting with 2 layers of 2-K paint (acrylic) in a single color in a RAL color of your choice, then sealing the cavities with special wax
• Rims in silver

Steel construction:
• Steel construction made of high-strength fine-grain steel.
• Steel qualities:
• S355J2+N/S355MC (yield strength 355MPa)
• S690QL/S700MC (yield strength 690MPa)
• Welders tested to DIN-EN 287-1
• Welding process MAG according to EN ISO 4063
• Shielding gas M21 according to EN ISO 14175

Accessories included:
• 2" king pins
• 3 pairs of countersunk lashing rings on the gooseneck (LC 6,300 daN)
• 4 wheel chocks with holder on the vehicle
• Lighting for the operation of the gooseneck, the suspension and the hydraulic tensioning with on and off switch
• Mechanical downpipe supports for approx. 48,000 kg support load
• Access ladder mounted in the front right, with 2 plug-in holding brackets
• The ladder can optionally be mounted by the customer on the front left side
• In front the axle unit, a removable full cover on both sides
• WABCO Roll Stability Support (RSS)
• 9 pairs of lashing rings (LC 6,300 daN) on the longitudinal beams.
• A grating support on the longitudinal beams at the same height between the guide rails of the load securing.
• Hydraulic preparation including control for the installation of 3 pairs of our hydraulic load securing devices.
• The first and last axles can be lifted manually on the left and right
• A storage box on the left and right behind the axle unit, splash-proof
• Bevel at the back to make it easier to insert the loading pallet
• Eyelets for mechanical bracing attached to the back of the end cross member
• Rear door with cross bracing, mounted on the left and hydraulically locked on the right, can be locked horizontally by approx. 90°, 105° and 270°
• Underrun protection can be folded upwards to transport a maximum of 4 empty standard pallets. Without width adjustment
• License plate with holder, including lighting, rear left on the trailer
• Partial HRM metallization (High Resistance Metallization)
Hnjlhjiuy Ntoccqpsn
• The entire steel construction is shot blasted, then the defined visible surfaces

El anuncio se tradujo automáticamente y se pueden haber producido errores de traducción.